Showing 97–108 of 202 resultsSorted by latest
-
– Fully-automated Erhardt+Leimer inspection system with lane flagging, Slitter, & Duplex rewinder.
– Max working inspection width of 54”.
– Line speed of up to 100 yds/min.
– Unwind/Inspection:
- Pinnacle Converting Equipment Co. Unwind stand
- Drop-in Safety chucks for output shaft, fitted with a pneumatic multi-caliper break system. Chucks are set to accept 1.5” square bar shafts. Air bars are included that fit 3” ID fiber cores.
- Automatic web tension control at the unwind, via an ultrasonic sensor.
- Accuweb, Inc. Micro1000 automatic edge guide system with ultrasonic sensor for +/- 3.0” correction.
- Unwind cradle is erected on linear rails + bearings with an electromechanical actuator to work alongside automatic edge-guide system for web alignment.
- Fore/aft adjustment screws to eliminate slack edge.
- Full plexi-glass housing and filtered blower providing positive pressure to mitigate dust ingress into the inspection area.
- Mounted air nozzles for web cleaning at unwind.
- Four (4) Erhardt+Leimer OL-5250 4K line scan cameras
- 12 kHz scan frequency with automatic focus, calibration, and chip alignment. 0.19 mm/px resolution on web.
- Two inspection lines of two cameras each, set at 90 degrees and 62.5 degrees inspection angles.
- Two (2) 70” Metaphase MetaBright LED line lights, setup for diffuse reflection, specular reflection, and transmission measurement.
- E+L ELSIS defect inspection, roll mapping, and roll reporting software, run by a linux-based PC.
- Full integration into flagging system located on rewind stand.
- Encoder-driven roll mapping and flagger timing.
– Flagger/Slitter/Duplex Rewinder:
- Pinnacle Converting Equipment Co. 60” Slitter Duplex Rewinder
- Can accept maximum 26” D, 2500 lbs. rolls on two (2) separate sets of drop-in safety chucks.
- Two (2) air bars that fit 3” ID fiber cores with 1.5” square bar ends.
- Seven (7) adjustable individual shear blades mounted on common dovetail bar. Bottom anvil rings.
- Pneumatic friction clutch to provide adjustable rewind tension. Tension controlled by ultrasonic sensor and I/P regulator.
- Red Lion G3 touchscreen control and HMI
- Seven (7) AF-2 web flagging modules with adjustable sliding bases, fully integrated into inspection system with encoder for accuracy.
– Additional:
- Vestil Steel Gantry Crane at unwind (3-axis movement)
- 4000 lbs. capacity frame with 2 ton Coffing electric hoist and spreader bar
- 12’ of track movement on floor
- Dimensions: 6’ L (wheelbase) x 15’ W (between tracks) x 10’ H
- Dayton Steel Gantry Crane at rewind (3-axis movement)
- 2000 lbs. capacity frame with 1 ton Dayton electric hoist and spreader bar
- 11’ of track movement on floor
- Dimensions: 5’ L (wheelbase) x 15’ W (between tracks) x 10’ H
- Quickdraft trim removal system
– Power: 460 VAC, 3 Phase, 60 Hz
– Pneumatic: 90 PSI
- Pinnacle Converting Equipment Co. Unwind stand
-
– 2001 Year
– 220 cm
– Horizontal Clip
– Lanly Gas Fired Dryer
– With Mahlo Weft Straightening
– One with Birch Brothers Entry & Exit
-
– Model PL-KS3B-HHS – II
– 2012 year
– 30″ cylinder diameter
– 18 gauge
– 90 feeders
– 1740 needles
– 440/60/3 voltage
