Showing all 6 results

  • (1) TUKAspread TS300 Automatic Fabric Spreading Machine

    Details
  • (1) Zinser Draw Winder

    Details
    • 144 position
    • 1999 year
    • Tube take-up
  • (1) Erdmann Drawtwister

    Details
    • 144 position
    • 2001 year
    • Pirn take-up
  • (1) Fully Automatic Slitter/Rewinder with E&L Virtual Inspection Machine – 2010 Year

    Details

    – Fully-automated Erhardt+Leimer inspection system with lane flagging, Slitter, & Duplex rewinder.

    – Max working inspection width of 54”.

    – Line speed of up to 100 yds/min.

    – Unwind/Inspection:

    • Pinnacle Converting Equipment Co. Unwind stand
      • Drop-in Safety chucks for output shaft, fitted with a pneumatic multi-caliper break system. Chucks are set to accept 1.5” square bar shafts. Air bars are included that fit 3” ID fiber cores.
      • Automatic web tension control at the unwind, via an ultrasonic sensor.
      • Accuweb, Inc. Micro1000 automatic edge guide system with ultrasonic sensor for +/- 3.0” correction.
      • Unwind cradle is erected on linear rails + bearings with an electromechanical actuator to work alongside automatic edge-guide system for web alignment.
      • Fore/aft adjustment screws to eliminate slack edge.
      • Full plexi-glass housing and filtered blower providing positive pressure to mitigate dust ingress into the inspection area.
      • Mounted air nozzles for web cleaning at unwind.
    • Four (4) Erhardt+Leimer OL-5250 4K line scan cameras
      • 12 kHz scan frequency with automatic focus, calibration, and chip alignment. 0.19 mm/px resolution on web.
      • Two inspection lines of two cameras each, set at 90 degrees and 62.5 degrees inspection angles.
      • Two (2) 70” Metaphase MetaBright LED line lights, setup for diffuse reflection, specular reflection, and transmission measurement.
      • E+L ELSIS defect inspection, roll mapping, and roll reporting software, run by a linux-based PC.
      • Full integration into flagging system located on rewind stand.
      • Encoder-driven roll mapping and flagger timing.

    – Flagger/Slitter/Duplex Rewinder:

    • Pinnacle Converting Equipment Co. 60” Slitter Duplex Rewinder
      • Can accept maximum 26” D, 2500 lbs. rolls on two (2) separate sets of drop-in safety chucks.
      • Two (2) air bars that fit 3” ID fiber cores with 1.5” square bar ends.
      • Seven (7) adjustable individual shear blades mounted on common dovetail bar. Bottom anvil rings.
      • Pneumatic friction clutch to provide adjustable rewind tension. Tension controlled by ultrasonic sensor and I/P regulator.
      • Red Lion G3 touchscreen control and HMI
      • Seven (7) AF-2 web flagging modules with adjustable sliding bases, fully integrated into inspection system with encoder for accuracy.

    – Additional:

    • Vestil Steel Gantry Crane at unwind (3-axis movement)
      • 4000 lbs. capacity frame with 2 ton Coffing electric hoist and spreader bar
      • 12’ of track movement on floor
      • Dimensions: 6’ L (wheelbase) x 15’ W (between tracks) x 10’ H
    • Dayton Steel Gantry Crane at rewind (3-axis movement)
      • 2000 lbs. capacity frame with 1 ton Dayton electric hoist and spreader bar
      • 11’ of track movement on floor
      • Dimensions: 5’ L (wheelbase) x 15’ W (between tracks) x 10’ H
    • Quickdraft trim removal system

    – Power: 460 VAC, 3 Phase, 60 Hz

    – Pneumatic: 90 PSI

  • DM&E Short Cut Recycling Machine

    Details
  • (1) Armstrong Cot Buffing Machine

    Details

    – Model L
    – with Automatic Traverse Device